-------------------------------------------------------
¦ How to code youre own "Fire" Routines ¦
-------------------------------------------------------
Hopefully this information file will give you all the information you
need to code youre own fire routines, seen in many demo's and also to
actually take it all further and develop youre own effects..
Ok, so lets get on....
Setting up
first thing we need to do is set up two arrays, the size of the arrays
depends on the many things, screen mode, speed of computer etc, its not
really important, just that they should both be the same size... I'll
use 320x200 (64000 byte) arrays for this text, because that happens to
be the size needed for using a whole screen in vga mode 13h.
The next thing we need to do is set a gradient palette, this can be
smoothly gradiated through ANY colours, but for the purpose of this
text lets assume the maximum value is a white/yellow and the bottom
value is black, and it grades through red in the middle.
Ok, we have two arrays, lets call them startbuffer and screenbuffer, so
we know whats going on. Firstly, we need to setup an initial value for
the start buffer... so what we need is a random function, that returns
a value between 0 and 199 (because our screen is 200 bytes wide) this
will give us the initial values for our random "hotspots" so we do this
as many times as we think is needed, and set all our bottom line values
of the start buffer to the maximum colour value. (so we have the last
300 bytes of the start buffer set randomly with our maximum colour,
usually if we use a full palette this would be 255 but it can be
anything that is within our palette range.)
Ok, thats set the bottom line up.. so now we need to add the effect,
for this we need to copy the start buffer, modify it and save it to the
screenbuffer, we do this by averaging the pixels (this is in effect
what each byte in our array represents) surrounding our target....
It helps to think of these operations in X,Y co-ordinates....
Lets try a little diagram for a single pixel.....
This is the startbuffer This is our screenbuffer
--------------------- ---------------------
¦0,0¦0,1¦0,2¦0,3¦0,4¦ etc... ¦ ¦ ¦ ¦ ¦ ¦
--------------------- ---------------------
¦1,0¦1,1¦1,2¦1,3¦1,4¦ etc.. ¦ ¦X,Y¦ ¦ ¦ ¦
--------------------- ---------------------
¦2,0¦2,1¦2,2¦2,3¦2,4¦ etc.. ¦ ¦ ¦ ¦ ¦ ¦
--------------------- ---------------------
Here we're going to calulate the value for X,Y (notice I didnt start at
0,0 for calculating our new pixel values?? thats because we need to
average the 8 surrounding pixels to get out new value.. and the pixels
around the edges wouldn't have 8 pixels surrounding them), so what we
need to do to get the value for X,Y is to average the values for all
the surrounding pixels... that means adding 0,0 0,1 0,2 + 1,0 1,2 + 2,0
2,1 2,2 and then dividing the total by 8 (the number of pixels we've
takes our averages from), but there's two problems still facing us..
1) The fire stays on the bottom line....
2) Its slow....
3) The fire colours dont fade...
Ok, so first thing, we need to get the fire moving! :) this is really
VERY easy. All we need to do is to take our average values from the
pixel value BELOW the pixel we are calculating for, this in effect,
moves the lines of the new array up one pixel... so for example our old
X,Y value we were calculating for was 1,1 so now we just calculate for
2,1 and put the calculated value in the pixel at 1,1 instead.. easy..
The second problem can be approached in a few ways.. first and easiest
is to actually calculate less pixels in our averaging.. so instead of
the 8 surrounding pixels we calculate for example, 2 pixels, the one
above and the one below our target pixel (and divide by 2 instead of 8)
this saves a lot of time, another approach is to use a screen mode,
where you can set 4 pixels at a time, or set up the screen so that you
can use smaller arrays (jare's original used something like 80X50 mode)
which in effect reduces to 1/4 the number of pixels needed to be
calculated.
The third problem is just a matter of decrementing the calculated value
that we get after averaging by 1 (or whatever) and storing that value.
Last but not least, we need to think about what else can be done...
well, you can try setting a different palette, you can also try setting
the pixel value we calculated from to another place, so say, instead of
calculating from one pixel below our target pixel, you use one pixel
below and 3 to the right of our target... FUN! :))
Well, I hope I didnt confuse you all too much, if you need anything
clearing up about this, then email me at pc@espr.demon.co.uk ok?
Written by Phil Carlisle (aka Zoombapup // CodeX) 1994.